DJIMissionManagerError

Unsupported feature error.
Where possible:
This error will be returned by the function for a special feature interface when the feature is not supported by the device.

Mission not existed

The aircraft's altitude is too high.

The aircraft's altitude is too low.

The aircraft is going home.

The aircraft is in a no fly zone.

The aircraft is landing.

The aircraft is not in the air.

The aircraft is running a mission.

The aircraft is starting the motor.

The aircraft is taking off.

The altitude is too high.

The altitude is too low.

Mission began (Phantom 2 series).

Mission canceled.

The aircraft cannot bypass the obstacle.

The distance from the mission target is too long.
For example, the distance from hotpoint target position is too long,
or the distance from the first waypoint target position is too long

Mission failed.

The feature points found by both vision sensors cannot match.

The disconnect time of the follow me mission is too long.

The distance between the aircraft and mobile phone is too large (must be lower than 20000m). This error will be returned when initializing the follow me task.

The initial pitch angle of the gimbal is too large.

The GPS of the aircraft is not ready.
Maybe the aircraft haven't got the home point location.

The GPS signal of the aircraft is weak.

A higher priority mission is executing.

The direction of the homepoint is unknown.

The latitude and longitude of the homepoint are invalid.

The homepoint is not paused.

The home point of the aircraft is not recorded.

Homepoint is paused.

The homepoint is not a valid float value.

The aircraft is in novice mode.

The type of IOC is unknown.

The IOC mode is working.

The aircraft is flying.

The API key provided to you is not at the correct permission level.
Check whether your key is a level 2 application key in your AndroidManifest.xml.

Low battery level warning.

The mode of the main controller is error.

The mission is across a no fly zone.

The condition of the mission is not satisfied.

There is a conflicting setting in the mission.

The entry point of the mission is invalid.

The estimated time for the mission is too long.

The heading mode of the mission is invalid.

The information for the mission is invalid.

The mission does not exist.

The mission is not initialized.

The parameters of the mission are invalid.

The radius of mission is invalid.

The radius of the mission is over the acceptable limit.

The mission resume failed.

The speed of the mission is too high.

The aircraft's control mode is in error.
Maybe the control mode is manual or attitude. Mode is Manual or Atti

The aircraft's motor has not started.

Navigation is not open.

The aircraft is not in auto mode.

No live video feed is captured for the ActiveTrack Mission.

The aircraft is not in the air. Please take off first.

Remote controller mode error.
You should put the remote controller's mode selection bar to F position.

The aircraft reaches the altitude lower bound of the TapFly Mission.

The aircraft has reached the flight limitation.

The aircraft is taking off.

Mission timeout.

Aircraft is too close to the home point.

The gimbal pitch is too low.

Obstacles are detected.

Mission is paused by user.

The tracking rectangle is too large.

The tracking rectangle is too small.

The tracking target is lost.

The ActiveTrack mission is too unsure the tracking object and confirmation is required.

The tracking target doesn't have enough features to lock onto.

The tracking target is shaking too much.

The tracking target is too close to the aircraft.

The tracking target is too far away from the aircraft.

The tracking target is too high.

Unknown result.

Navigation in the product is unsupported.

Waypoint mission has reached the maximum points limit.
1. Phantom 2 Vision/Vision+: the max points limit is 16.
2. Inspire1/ Phantom 3 series: the max points limit is 99.

Mission was stoped by the user.

The frame rate of the live video feed is too low.

The data from the vision system is abnormal.

The quality of vision sensor is low.

The vision sensors are overexposed.

The vision sensors are underexposed.

The vision system encounters system error.

The vision system requires calibration.

The vision system cannot get the authorization to control the aircraft.

The waypoints are still uploading.

The parameter of the waypoint action is invalid.

The damping check failed.

The waypoint distance is too close.

The waypoint destance is too long.

The idle velocity is invalid.

The index of the waypoint is out of range.

The information for the waypoint is invalid.

The information for the waypoint mission is not completely uploaded.

The waypoint mission is not running.

The waypoint mission is running.

The total trace of the waypoint is too long.

The trace of the waypoint is too long.

Waypoint is uploading.

The waypoint uploading is not complete.

The command is wrong.

Returns the specific error in DJIMissionManagerError according to the error code.

Returns the description of the error code.

Sets the description for the error code.